The plugin will create one indigo device for each BLE device found.The plugin piBeacon will communicate with and configure 1-10 raspberyPi's to be detectors for the BLE devices. They are set/managed and read by the plugin ,see if you like you can connect sensors or digital inputs or outputs to the rPi. a bluetooth dongle connected to the USB port on the rPi (rpi3 comes with all required devices included)ĥ. The reaction time is ~ 5-10 seconds to show UP when the Phone enters the range of an rPi.Ī simple step by step for a basic setup is here:Īnd the word file, if someone was to add:ģ. This means you can use your (i)Phone as presence detector. It will deliver info UP/Down RSSI and TxPower -can be used similar to an iBeacon. It will initiate a connection, wait for the first package back and stop. With V > 1.17 you can connect to any BLE enabled device.With version >1.8 you can attached different sensors (temp, humidity, pressure, light, analog voltage, resistor measurements, IR switches, PIR, gyroscope, magnetometer, microwave sensor etc) and use GPIO pins or a DAC as output to drive e.g.The UUIDs can be the same, - The plugin will be using the MAC number to identify each iBeacon and show the UUID-Major-Minor in the notes field. It will allow bluetooth v4 (BLE) iBeacons to be used as presence detector devices with very fast reaction time (~ 0.5 seconds) and independent of any internet connection.Įach iBeacon has a unique MAC number as well as a UUID-Major-Minor number.In order to re-enter normal operational model, simply remove and replace power to the device. Reboot the beacon into Direct Firmware Update mode.Ĭontact Radius Networks support for information on the procedure for firmware update or replacement. Press the Action Menu button and select DFU. In order to re-enter configurable mode for a RadBeacon X2, remove the front cover and switch the beacon power switch to OFF and back to ON.Ī beacon set in configurable mode will be configurable for up to 30 minutes or until you lock the device again. In order to re-enter configurable mode for a RadBeacon Tag, remove the front cover and press the configuration push button switch near the coin cell battery. In order to re-enter configurable mode for a RadBeacon USB, remove and restore power to the device. The Lock feature is a security precaution to limit the possibility of third party manipulation of your beacons once they have been installed and configured. Submit a valid PIN to prevent connections from remote Bluetooth 4.0 devices to the beacon configuration service. Press the Action Menu button and select Lock. Submit a valid PIN to reset the settings for your beacon to factory defaults. Reset the device to the original factory settings. Press the Action Menu button and select Reset. Submit a new and existing PIN to update the PIN for your beacon. Press the Action Menu button and select Update PIN. Validate the accuracy of your beacon settings by quickly verifying the ranging behavior of your device in proximity to your configured beacon. Press the Action Menu button and select Range. Update the measured power value with the results of your calibration activity and update your settings. Press the Action Menu button and select Calibrate.Ĭalibrate the measured power value of the beacon settings to ensure optimal proximity events and ranging. Submit a valid PIN to update the settings for this beacon. (If the RadBeacon is not configurable, then an "unable to connect" message will be displayed after approximately 15 seconds.) The settings displayed include: If the RadBeacon is configurable, its detailed settings will be displayed. Each beacon discovered is displayed with the following summary details Scan for nearby configurable RadBeacons by pressing the SCAN button. Once discovered, if the beacon is configurable, you can display each beacon's operating settings and make modifications to those settings. With the RadBeacon app you can scan for nearby Radius Networks beacons. The RadBeacon app from Radius Networks requires an Android device running Android 4.3 or higher and equipped with Bluetooth 4.0 capabilities. The RadBeacon™ app is the configuration utility for RadBeacon proximity beacons from Radius Networks that support Apple's iBeacon™ proximity services and the AltBeacon proximity services for Android devices.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |